How To Install A Corner Shower In Basement
How to Install a Fiberglass Base Over Concrete
Updated: Dec. 03, 2022
Plumb the drain using a special leak-proof drain assembly
Install a fiberglass shower stall over a concrete floor using a special drain assembly that eliminates leaks. Y'all run the drain line under the concrete.
You lot might besides similar: TBD
Step 1. Shower Drain Installation: Run a drainpipe nether the physical flooring
Shower stall on concrete
A shower usually requires a 2-in. drain, with the P-trap located under the concrete slab.
If yous want to install a shower over a concrete floor, a fiberglass shower stall will work simply fine. Ideally, you'll already accept a drain roughed in, with the piping sticking a few inches above the floor. Otherwise you have to break through the concrete to run a new line for a shower stall installation.
If you lot have a pipage stubbed up, call the plumber or contractor who did the work to ostend it. The 2-in. pipe is typically the shower or tub bleed. Line it upwards exactly with the drain hole in the bottom of your shower bay. This position determines the location of the stud walls effectually the shower. The supplier may be able to provide a dimensioned drawing of the shower bay, and so you don't actually have to put information technology in first.
If the existing 2-in. drainpipe isn't where you want information technology, you'll have to break up the physical and replumb the drain.
Make sure the drainpipe extends at to the lowest degree an inch in a higher place the concrete. If the pipe is besides short, you'll have to pause upwardly the concrete and extend it. Likewise, you'll need at to the lowest degree a 1-i/2-in. space between the pipe and the concrete to adapt the bleed assembly (see photo below). If there isn't, carefully chisel out the concrete around the pipe.
Tip: If you're considering a unmarried-piece shower bay, make sure y'all can get it into the new bath space. You may have to bring the unit into the space earlier framing the doorway or walls. If admission is a trouble, check out multiple-piece units that will fit through doorways more than easily.
Step 2. Shower Drain Installation: Mount the leakproof drain assembly
Drain assembly shut-upwards
The assembly locks tightly to the pipe and clamps to the border of the shower base to make leakproof seals.
Later on you frame the shower walls to fit the shower bay, lay the bay on its back and install the shower drain. Use a special leakproof shower drain associates called the No-Caulk Shower Drain. It'due south bachelor at dwelling centers and plumbing supply houses. Although these drain baskets are bachelor in plastic, I'd opt for the brass one. Follow these steps to attach the shower to the drain:
- Roll out a coil (about the diameter of a pencil) of plumber'due south putty (bachelor at all hardware stores) and wrap information technology nether the bleed basket flange.
- Agree the shower bleed handbasket in position in the shower bay drain pigsty, slide on the washers, and then thread on and hand-tighten the exterior setting ring. Tighten the ring with a large slip-joint pliers until it'due south firmly in place. You shouldn't be able to motility the shower basket past hand. The plumber's putty will squeeze out.
- Lower the shower bay and basket assembly over the drainpipe. Marker the piping most 3/4 in. beneath the drain basket flange.
- Lift the shower bay out of the way and cutting the drainpipe to length. A hacksaw works well. Make sure to cutting the pipe square, not angled.
- Set the shower bay and handbasket assembly dorsum over the piping. Slide the caulking gasket over the piping and button it all the way down so it sits against the lip at the bottom of the drain basket. Y'all may take to tap this gasket into place with a hammer and a thin piece of wood.
- Thread on the caulking nut and firmly tighten to compress the caulking gasket and seal the pipe. Use the slotted bar tool that comes with the drain assembly. Stick the flat blade of a screwdriver into the bar'southward slot and firmly hand-tighten.
- Snap on the perforated bleed comprehend (not shown).
Required Tools for this Projection
Take the necessary tools for this DIY shower drain installation project lined up earlier yous showtime—you'll save time and frustration.
Apartment-blade screwdriver
Required Materials for this Project
Avoid final-infinitesimal shopping trips by having all your materials ready ahead of time for a shower stall installation. Here's a list.
Originally Published: December 03, 2022
Source: https://www.familyhandyman.com/project/how-to-install-a-fiberglass-base-over-concrete/
Posted by: powelllize1960.blogspot.com
0 Response to "How To Install A Corner Shower In Basement"
Post a Comment